AT49BV001NT-12JC belongs to the category of non-volatile memory devices.
This product is primarily used for storing and retrieving digital information in electronic systems.
The AT49BV001NT-12JC is available in a 32-pin PLCC (Plastic Leaded Chip Carrier) package.
The essence of this product lies in its ability to provide reliable and non-volatile storage for electronic systems.
The AT49BV001NT-12JC is typically packaged in reels or tubes, with a quantity of 1000 units per package.
The AT49BV001NT-12JC has a total of 32 pins, each serving a specific function. Here is a detailed pin configuration:
The AT49BV001NT-12JC utilizes flash EEPROM technology to store and retrieve digital information. It consists of a grid of memory cells that can be electrically programmed and erased. When data is written, an electrical charge is applied to the memory cell, altering its state. This stored state can be read back later. The device uses a combination of address lines and control signals to access specific memory locations and perform read, write, or erase operations.
The AT49BV001NT-12JC finds applications in various electronic systems, including but not limited to: - Embedded systems - Consumer electronics - Automotive electronics - Industrial control systems - Communication devices
These alternative models offer different storage capacities, temperature ranges, and performance characteristics to cater to specific application requirements.
In conclusion, the AT49BV001NT-12JC is a non-volatile memory device that provides reliable and high-capacity storage for electronic systems. With its fast access time, low power consumption, and versatile interface, it offers several advantages for various applications. However, it has limitations in terms of erase/program cycle endurance and cost per bit. Understanding
Sure! Here are 10 common questions and answers related to the application of AT49BV001NT-12JC in technical solutions:
Q: What is the AT49BV001NT-12JC? A: The AT49BV001NT-12JC is a 1-megabit (128K x 8) CMOS flash memory device manufactured by Atmel.
Q: What are the key features of the AT49BV001NT-12JC? A: Some key features include a 12ns access time, low power consumption, and compatibility with both 3V and 5V systems.
Q: How can I interface the AT49BV001NT-12JC with my microcontroller? A: The AT49BV001NT-12JC uses a standard parallel interface, making it compatible with most microcontrollers.
Q: Can I use the AT49BV001NT-12JC as a storage device for my embedded system? A: Yes, the AT49BV001NT-12JC can be used as a non-volatile storage device for storing program code or data in embedded systems.
Q: What is the maximum operating frequency of the AT49BV001NT-12JC? A: The AT49BV001NT-12JC can operate at frequencies up to 83MHz, allowing for fast read and write operations.
Q: Does the AT49BV001NT-12JC support in-system programming (ISP)? A: No, the AT49BV001NT-12JC does not support in-system programming. It requires a separate programmer for programming and erasing.
Q: Can I use the AT49BV001NT-12JC in automotive applications? A: Yes, the AT49BV001NT-12JC is designed to meet the requirements of automotive applications, including temperature and voltage ranges.
Q: What is the typical power consumption of the AT49BV001NT-12JC? A: The AT49BV001NT-12JC has a typical standby current of 10µA and a typical active current of 20mA during read or write operations.
Q: Can I use the AT49BV001NT-12JC in battery-powered devices? A: Yes, the low power consumption of the AT49BV001NT-12JC makes it suitable for use in battery-powered devices where power efficiency is important.
Q: Are there any specific precautions I need to take when handling the AT49BV001NT-12JC? A: It is recommended to follow standard ESD (electrostatic discharge) precautions when handling the AT49BV001NT-12JC to prevent damage to the device.
Please note that these answers are general and may vary depending on the specific application and requirements.