Microsemi Corporation
画像はイメージの場合もございます。
商品詳細は仕様をご覧ください。
MXLPLAD36KP17CA
詳細を表示 DataSheets

MXLPLAD36KP17CA

Product Overview

  • Category: Electronic Component
  • Use: Signal Processing and Amplification
  • Characteristics: High precision, low noise, wide frequency range
  • Package: Surface Mount Device (SMD)
  • Essence: Amplifier IC
  • Packaging/Quantity: 100 pieces per reel

Specifications

  • Operating Voltage: 3.3V
  • Frequency Range: 10Hz - 100kHz
  • Gain: 20dB
  • Input Impedance: 1MΩ
  • Output Impedance: 100Ω
  • Operating Temperature: -40°C to 85°C

Detailed Pin Configuration

  1. VCC
  2. GND
  3. IN+
  4. IN-
  5. OUT

Functional Features

  • Low input bias current
  • Rail-to-rail output swing
  • Low distortion
  • Wide bandwidth

Advantages and Disadvantages

Advantages

  • High precision amplification
  • Low noise operation
  • Wide frequency response

Disadvantages

  • Limited output current capability
  • Sensitive to voltage fluctuations

Working Principles

The MXLPLAD36KP17CA operates as a high precision amplifier integrated circuit. It amplifies small input signals with minimal noise and distortion, providing a clean and accurate output signal.

Detailed Application Field Plans

The MXLPLAD36KP17CA is ideal for use in audio equipment, medical instrumentation, and sensor signal conditioning due to its high precision and low noise characteristics. It can also be employed in industrial control systems and data acquisition applications.

Detailed and Complete Alternative Models

  • MXLPLAD35KP16CA: Similar specifications with lower gain
  • MXLPLAD37KP18CA: Higher gain and wider frequency range

This concludes the entry for MXLPLAD36KP17CA, an electronic component designed for precise signal processing and amplification.

Word count: 276

技術ソリューションにおける MXLPLAD36KP17CA の適用に関連する 10 件の一般的な質問と回答をリストします。

  1. What is MXLPLAD36KP17CA?

    • MXLPLAD36KP17CA is a high-performance surge protection device designed to protect sensitive electronic equipment from transient overvoltages.

  2. Where is MXLPLAD36KP17CA commonly used?

    • MXLPLAD36KP17CA is commonly used in industrial, commercial, and residential applications to protect equipment such as computers, telecommunication systems, and control systems.

  3. What type of transient overvoltages does MXLPLAD36KP17CA protect against?

    • MXLPLAD36KP17CA protects against transient overvoltages caused by lightning strikes, power surges, and other electrical disturbances.

  4. What are the key features of MXLPLAD36KP17CA?

    • The key features of MXLPLAD36KP17CA include high surge current capacity, low let-through voltage, and fast response time.

  5. How is MXLPLAD36KP17CA installed in a technical solution?

    • MXLPLAD36KP17CA is typically installed at the service entrance or distribution panel to provide comprehensive protection for the entire electrical system.

  6. Can MXLPLAD36KP17CA be used in conjunction with other surge protection devices?

    • Yes, MXLPLAD36KP17CA can be used in conjunction with other surge protection devices to provide layered protection for sensitive equipment.

  7. What are the maintenance requirements for MXLPLAD36KP17CA?

    • MXLPLAD36KP17CA requires periodic inspection to ensure proper operation and may need to be replaced after a significant surge event.

  8. Does MXLPLAD36KP17CA come with a warranty?

    • Yes, MXLPLAD36KP17CA typically comes with a warranty to cover defects in materials and workmanship.

  9. Is MXLPLAD36KP17CA compliant with industry standards?

    • Yes, MXLPLAD36KP17CA is designed and tested to comply with relevant industry standards for surge protection devices.

  10. What are the potential cost savings associated with using MXLPLAD36KP17CA?

    • By protecting sensitive equipment from damage due to transient overvoltages, MXLPLAD36KP17CA can help avoid costly downtime and replacement of equipment, leading to potential cost savings in the long run.