Texas Instruments
画像はイメージの場合もございます。
商品詳細は仕様をご覧ください。
TLC27M4BIDR
詳細を表示 DataSheets

TLC27M4BIDR

Product Overview

  • Category: Integrated Circuit (IC)
  • Use: Operational Amplifier
  • Characteristics: Low-power, Rail-to-Rail Output, Quad Op-Amp
  • Package: SOIC (Small Outline Integrated Circuit)
  • Essence: The TLC27M4BIDR is a low-power quad operational amplifier designed for general-purpose applications.
  • Packaging/Quantity: The TLC27M4BIDR is available in a 14-pin SOIC package and is typically sold in reels of 2500 units.

Specifications

  • Supply Voltage: ±2 V to ±16 V
  • Input Offset Voltage: 1 mV (maximum)
  • Input Bias Current: 20 pA (maximum)
  • Slew Rate: 3.6 V/µs (typical)
  • Gain Bandwidth Product: 2.2 MHz (typical)
  • Operating Temperature Range: -40°C to +125°C

Detailed Pin Configuration

The TLC27M4BIDR has a total of 14 pins, which are assigned as follows:

  1. OUT1: Output of Op-Amp 1
  2. IN-1: Inverting Input of Op-Amp 1
  3. IN+1: Non-Inverting Input of Op-Amp 1
  4. V-: Negative Power Supply
  5. IN+2: Non-Inverting Input of Op-Amp 2
  6. IN-2: Inverting Input of Op-Amp 2
  7. OUT2: Output of Op-Amp 2
  8. V+: Positive Power Supply
  9. OUT3: Output of Op-Amp 3
  10. IN-3: Inverting Input of Op-Amp 3
  11. IN+3: Non-Inverting Input of Op-Amp 3
  12. OUT4: Output of Op-Amp 4
  13. IN+4: Non-Inverting Input of Op-Amp 4
  14. IN-4: Inverting Input of Op-Amp 4

Functional Features

  • Low-power consumption makes it suitable for battery-powered applications.
  • Rail-to-rail output allows the amplifier to operate with input and output signals that can swing close to the supply rails.
  • Quad op-amp configuration provides four independent amplifiers in a single package, saving board space and reducing component count.

Advantages and Disadvantages

Advantages

  • Low power consumption extends battery life in portable devices.
  • Rail-to-rail output enables accurate signal amplification even at low supply voltages.
  • Quad op-amp configuration reduces board space and simplifies circuit design.

Disadvantages

  • Limited gain bandwidth product may not be suitable for high-frequency applications.
  • Input offset voltage may introduce errors in precision measurement circuits.

Working Principles

The TLC27M4BIDR is based on the operational amplifier (op-amp) architecture. It utilizes differential inputs to amplify the voltage difference between its inverting and non-inverting inputs. The amplified output is then fed back to the inverting input through a feedback network, which sets the gain and stability of the amplifier. The rail-to-rail output stage ensures that the output voltage can swing close to the supply rails, maximizing the dynamic range of the amplifier.

Detailed Application Field Plans

The TLC27M4BIDR is widely used in various applications, including:

  1. Signal conditioning and amplification in sensor interfaces.
  2. Active filters and equalizers in audio systems.
  3. Voltage and current measurement circuits.
  4. Battery-powered instrumentation and data acquisition systems.
  5. Industrial control and automation systems.

Detailed and Complete Alternative Models

  • LM324: Similar quad operational amplifier with a wider supply voltage range.
  • TL074: Quad op-amp with higher gain bandwidth product for higher-frequency applications.
  • MCP6004: Low-power quad op-amp with rail-to-rail input and output capabilities.

These alternative models offer similar functionality to the TLC27M4BIDR and can be considered as replacements depending on specific application requirements.

Word count: 452 words

技術ソリューションにおける TLC27M4BIDR の適用に関連する 10 件の一般的な質問と回答をリストします。

Sure! Here are 10 common questions and answers related to the application of TLC27M4BIDR in technical solutions:

  1. Q: What is the TLC27M4BIDR? A: The TLC27M4BIDR is a precision operational amplifier (op-amp) that is commonly used in various technical applications.

  2. Q: What are the key features of the TLC27M4BIDR? A: The key features of the TLC27M4BIDR include low offset voltage, low input bias current, high open-loop gain, wide supply voltage range, and low power consumption.

  3. Q: What are some typical applications of the TLC27M4BIDR? A: The TLC27M4BIDR can be used in applications such as signal conditioning, amplification, filtering, sensor interfaces, data acquisition systems, and control systems.

  4. Q: What is the supply voltage range for the TLC27M4BIDR? A: The TLC27M4BIDR can operate with a supply voltage range of 3V to 16V.

  5. Q: What is the input offset voltage of the TLC27M4BIDR? A: The input offset voltage of the TLC27M4BIDR is typically very low, around 500µV.

  6. Q: What is the input bias current of the TLC27M4BIDR? A: The input bias current of the TLC27M4BIDR is typically very low, around 20pA.

  7. Q: Can the TLC27M4BIDR operate in single-supply configurations? A: Yes, the TLC27M4BIDR can operate in both single-supply and dual-supply configurations.

  8. Q: What is the maximum output current of the TLC27M4BIDR? A: The maximum output current of the TLC27M4BIDR is typically around 20mA.

  9. Q: Is the TLC27M4BIDR suitable for low-power applications? A: Yes, the TLC27M4BIDR has a low power consumption, making it suitable for low-power applications.

  10. Q: Can the TLC27M4BIDR be used in temperature-sensitive environments? A: Yes, the TLC27M4BIDR has a wide operating temperature range and can be used in temperature-sensitive environments.

Please note that these answers are general and may vary depending on specific datasheet specifications and application requirements.