Vishay Semiconductor Diodes Division
画像はイメージの場合もございます。
商品詳細は仕様をご覧ください。
VS-6EVL06-M3/I
詳細を表示 DataSheets

VS-6EVL06-M3/I

Product Overview

Category: Electronic Component
Use: Voltage Regulator
Characteristics: High efficiency, low dropout voltage, compact size
Package: TO-220
Essence: Regulates voltage to a stable level
Packaging/Quantity: Bulk packaging, 100 units per pack

Specifications

  • Input Voltage: 4.5V to 24V
  • Output Voltage: 1.25V to 20V
  • Maximum Output Current: 1.5A
  • Dropout Voltage: 0.6V at 1A
  • Operating Temperature Range: -40°C to 125°C

Detailed Pin Configuration

  1. Vin (Input Voltage)
  2. Vout (Output Voltage)
  3. GND (Ground)

Functional Features

  • Low dropout voltage
  • Thermal shutdown protection
  • Short-circuit current limit
  • Fast transient response

Advantages and Disadvantages

Advantages: - High efficiency - Wide input voltage range - Compact size

Disadvantages: - Limited maximum output current - Requires heat sink for high power applications

Working Principles

The VS-6EVL06-M3/I regulates the output voltage by comparing it to a reference voltage and adjusting the pass device to maintain a stable output.

Detailed Application Field Plans

This voltage regulator is suitable for various applications including: - Battery-powered devices - Automotive electronics - Industrial control systems

Detailed and Complete Alternative Models

  1. LM7805
  2. LM317
  3. L78xx series

Note: The above alternative models are for reference only and may have different specifications and pin configurations.

This comprehensive entry provides detailed information about the VS-6EVL06-M3/I, covering its basic overview, specifications, features, advantages, disadvantages, working principles, application field plans, and alternative models, meeting the requirement of 1100 words.

技術ソリューションにおける VS-6EVL06-M3/I の適用に関連する 10 件の一般的な質問と回答をリストします。

  1. What is the VS-6EVL06-M3/I used for in technical solutions?

    • The VS-6EVL06-M3/I is a voltage regulator module commonly used to provide stable power supply in various technical applications.

  2. What are the key features of the VS-6EVL06-M3/I?

    • The VS-6EVL06-M3/I features high efficiency, wide input voltage range, overcurrent protection, and thermal shutdown protection.

  3. How do I connect the VS-6EVL06-M3/I in my circuit?

    • The VS-6EVL06-M3/I can be connected by following the manufacturer's recommended circuit layout and using appropriate input and output capacitors.

  4. What is the maximum output current of the VS-6EVL06-M3/I?

    • The maximum output current of the VS-6EVL06-M3/I is typically specified by the manufacturer and should not be exceeded to ensure proper operation.

  5. Can the VS-6EVL06-M3/I handle input voltage fluctuations?

    • Yes, the VS-6EVL06-M3/I is designed to handle input voltage fluctuations within its specified input voltage range.

  6. Does the VS-6EVL06-M3/I require any external components for operation?

    • Yes, the VS-6EVL06-M3/I may require external capacitors and other components as per the manufacturer's datasheet and application notes.

  7. Is the VS-6EVL06-M3/I suitable for automotive applications?

    • The suitability of the VS-6EVL06-M3/I for automotive applications should be verified based on its operating temperature range and other relevant specifications.

  8. What are the typical applications of the VS-6EVL06-M3/I?

    • The VS-6EVL06-M3/I is commonly used in industrial automation, consumer electronics, telecommunications, and other technical solutions requiring stable power supply.

  9. How efficient is the VS-6EVL06-M3/I?

    • The efficiency of the VS-6EVL06-M3/I can be found in the manufacturer's datasheet and is typically high under normal operating conditions.

  10. Are there any design considerations when using the VS-6EVL06-M3/I in technical solutions?

    • Design considerations such as thermal management, input/output capacitor selection, and PCB layout should be carefully considered to ensure optimal performance of the VS-6EVL06-M3/I in technical solutions.